NEWS & INSIGHTS

Selection know-how, maintenance practice and group news

Site experience written up as reusable method, plus reference material for project decisions.

2026-11-10
Selection Guide

How to Specify a Screw Compressor: Flow, Pressure and Load Profile

Selection starts with measured air demand, not motor power. Sum the consumption of equipment running simultaneously and add 10–20% headroom; where demand is intermittent, add receiver volume rather than oversizing the compressor.

Pressure comes next. Every additional bar of discharge pressure raises energy use by roughly 6–8%, so set the duty point from the lowest end-use requirement plus line loss. Finally, check the load profile: steady full load favours fixed-speed or two-stage, strong swings favour permanent-magnet VSD.

2025-12-18
Energy Saving

Why Two-Stage Compression Saves Energy: the Role of Intercooling

Compressing air raises its temperature, and compression work rises with it. Two-stage machines split the pressure ratio into two steps and use an intercooler to bring the air back close to inlet temperature before the second stage, so total work is clearly lower than single-stage.

The benefit depends on pressure ratio and operating point: higher discharge pressure and longer running hours make two-stage the better choice, while low-pressure, stop-start users may be better served by a VSD single-stage. Compare energy, not just purchase price.

2025-10-22
Maintenance

Setting Replacement Intervals for Filters and Lubricant

Oil filters and separators are usually changed on running hours, with shorter air-filter intervals on dusty sites. A more reliable rule is to watch differential pressure: replace the separator once it exceeds the maker's limit or oil carry-over rises.

Lubricant condition governs airend life. Heat and humidity accelerate oxidation, so sample oil for viscosity and acid number on running hours rather than following a calendar blindly. Never mix lubricants from different brands — it invites carbon build-up and emulsification.

2025-09-15
Drilling Match

Matching a DTH Rig to Its Compressor

DTH penetration is governed mainly by the air flow and pressure the hammer needs. Once the rig is chosen, size the compressor from the hammer's rated consumption and working pressure — not from rig weight. Insufficient flow means weak impact, slower penetration and abnormal bit wear.

High-pressure hammers (1.7 MPa and above) need high-pressure compressors; running them on a conventional 0.8 MPa unit costs penetration rate and hole quality. Deep holes also require accounting for line loss and leakage as depth increases.

2025-08-06
Group News

Kaishan Two-Stage Screw Technology Listed in National Energy-Saving Catalogue

Kaishan's two-stage oil-injected screw compressor technology was added to the national key energy-saving technology promotion catalogue. Two-stage compression with intercooling lowers energy per cubic metre and has been applied at scale on mining, hydropower and railway projects.

For Chinese users, inclusion in the catalogue eases policy and financing support for retrofit and new-build projects, and supports efficiency cases on export projects.

2025-06-30
Group News

Compressor Company Certified to ISO14001 and OHSAS18001

Kaishan's compressor company was certified to ISO14001 environmental management and OHSAS18001 occupational health and safety, completing its management certification structure alongside existing quality certification.

For overseas buyers these are baseline items in supplier audits and, together with CE, MA and energy-saving product certification, cover admission requirements on most international projects.

2025-04-12
Overseas Projects

Austrian LMF Cryogenic Unit Rolls Out at Kaishan Lingang Base

A cryogenic unit from Austria's LMF, acquired by Kaishan, rolled out at the Lingang base in Shanghai, marking deeper local manufacturing capability for high-pressure and cryogenic compressors.

LMF has long built high-pressure piston compressors up to 700 bar for oil, chemical and gas industries; after the acquisition the two businesses combine manufacturing and market resources.

2025-03-05
Industry Knowledge

How Much Does Permanent-Magnet VSD Save on Varying Load?

Savings depend on how much demand varies. When flow oscillates between 60% and 80% of rated output, a VSD machine saves clearly against a fixed-speed unit cycling load/unload; at sustained full load the gap narrows.

Record a week of demand before deciding, then compare energy at the actual operating points rather than applying a claimed “30% saving”. For multi-unit stations, one VSD machine sequenced with fixed-speed units is often more economical than an all-VSD lineup.

RFQ

Need a selection or spare-parts quote?

Send us your duty: industry, air flow or hole size and depth, pressure and site conditions. We reply with a model recommendation and lead time.

+86 186 0902 3297 Email